OSCam/en/examples/Reader

OSCam Übersicht OSCam Home OSCam Accueil OSCam Home

Example Reader Configurations

The reader is the module that allows OSCam server to translate ECMs received from clients into CWs, which are sent back to clients for decrypting channels. There are two types of readers: hardware readers, which are somehow connected to the machine which runs OSCam server, and remote readers, which are running on different machines than the one running the OSCam server.

For the hardware readers, OSCam needs to know what type the reader is, how it is connected to the machine, what protocol it "speaks", and what subscription cards are inserted in that device.

For the remote readers, OSCam must know the IP address and port where to connect, the protocol spoken, and how to authenticate itself (username/password). Again, you can specify subscriptions that can be found there.

The following list shows example configurations for the supported readers.

Serial-Mouse kompatible Reader

[reader]
label    = myserialmouserreader
protocol = mouse
detect   = CD
device   = /dev/ttyS0
group    = 1
emmcache = 1,3,2
services = myservice,thisservice
caid     = 0100

USB-Mouse kompatible Reader

[reader]
label     = myusbmousereader
protocol  = mouse
detect    = CD
device    = /dev/ttyUSB0
aeskey    = 0102030405060708090a0b0c0d0e0f10
group     = 2
emmcache  = 1,3,2
services  = services2
caid      = 0200

Remote Camd3.78x Reader with fallback for group 1

[reader]
label     = mycamd378xreader
protocol  = cs378x
device    = 192.168.0.1,1234
user      = user1,
password  = password1
group     = 1
fallback  = 1

Remote Newcamd Reader with fallback for group 2

[reader]
label     = mynewcamdreader
protocol  = newcamd
key       = 0102030405060708091011121314
device    = 192.168.0.2,2345
user      = user2
password  = password2
group     = 2
fallback  = 1

Remote CCcam Reader

[reader]
label     = mycccamreader
protocol  = cccam
device    = 192.168.0.3,3456
user      = user3
password  = password3
group     = 3
caid      = 0300,0400,0500
cccversion= 1.2.3
cccbuild  = 4567

PCSC Reader

[reader]
label     = mypcscreader
protocol  = pcsc
device    = 0
aeskey    = 0102030405060708090a0b0c0d0e0f10
group     = 4
caid      = 0600

Smargo Smartreader+

# example 1
[reader]
label     = mysmargoreader
protocol  = smartreader
device    = 001:002
aeskey    = 0102030405060708090a0b0c0d0e0f10
group     = 5
caid      = 0700

# example 2
[reader]
label      = mysmargoreader
protocol   = smartreader
device     = Serial:Reader 1
detect     = cd
mhz        = 600
cardmhz    = 600
emmcache   = 1,3,2
group      = 5
services   = my_services

Internal Reader

[reader]
label     = myinternalreader
protocol  = internal
device    = /dev/sci0
group     = 6
caid      = 0800

Constant CW

[reader]
label     = myconstantcw
protocol  = constcw
device    = /var/keys/constant.cw
group     = 7

Remote Radegast Reader

[reader]
label        = myradegastreader 
protocol     = radegast
device       = 192.168.0.6,56789
group        = 9
caid         = 0500

AD-Teknik

AB Multiprogrammer 3.5 serial

[reader]
label        = mymultiprogrammer3.5
protocol     = mp35
detect       = CD
device       = /dev/ttyS1
group        = 10
emmcache     = 1,3,2
services     = services10
caid         = 0900

AB Multiprogrammer 3.6. USB

[reader]
label        = mymultiprogrammer3.6
protocol     = mp35
detect       = CD
device       = /dev/ttyUSB1
group        = 11
emmcache     = 1,3,2
services     = services11
caid         = 1000

AB USB Phoenix at 6.00 mhz

[reader]
label        = mymultiprogrammerUSBPhoenix
protocol     = mp35
detect       = CD
device       = /dev/ttyUSB2
mhz          = 600
group        = 12
emmcache     = 1,3,2
services     = services12
caid         = 1100

sc8in1 reader

[reader]
label        = mysc8in1reader
protocol     = sc8in1
device       = /dev/ttyUSB0:1
group        = 13
emmcache     = 1,3,2
services     = services11
caid         = 1200

Smargo Special

First, read about udev => http://en.wikipedia.org/wiki/Udev

Smargo readers do not offer clear identification in a standard manner, at least before firmware 1.04. Starting from firmware 1.04, one can assign a clear identifier with the Smargo tools. To find out how to set the identifier (the clear name), please refer to the Smargo tool documentation, which should be included in the Smargo tools package.

The following example shows three Smargos and a MasterCRD on Debian Linux.

We remove all Smargos from the PC and attach them in sequence, while using Smargo tools to identify each device, as follows:

cd /where/the/smargotools/are # change directory to where Smargo tools are

# Attach first Smargo WITHOUT card, in a different USB slot, and then...
./srp_tool -n 1 # we assign identifier "1" to this device, later assigned to OSCam as "Serial:Reader 1"

# Attach another Smargo, then...
./srp_tool -n 2 # we assign identifier "2" to this device, later assigned to OSCam as "Serial:Reader 2"

# and so on...

An example using udev-rules:

# provide new udev-rules
vi /lib/udev/rules.d/10-usb-name-for-example.rules

# then type as follows:

# Smargo 1
SUBSYSTEMS=="usb", KERNEL=="ttyUSB*", ATTRS{serial}=="Reader 1", ATTRS{idVendor}=="0403", ATTRS{idProduct}=="6001", SYMLINK+="smargo1", MODE="0666"
# Smargo 2
SUBSYSTEMS=="usb", KERNEL=="ttyUSB*", ATTRS{serial}=="Reader 2", ATTRS{idVendor}=="0403", ATTRS{idProduct}=="6001", SYMLINK+="smargo2", MODE="0666"
# Smargo 3
SUBSYSTEMS=="usb", KERNEL=="ttyUSB*", ATTRS{serial}=="Reader 3", ATTRS{idVendor}=="0403", ATTRS{idProduct}=="6001", SYMLINK+="smargo3", MODE="0666"
# MasterCRD over Serial connector *************************
SUBSYSTEMS=="usb", KERNEL=="ttyUSB*", ATTRS{idVendor}=="4711", ATTRS{idProduct}=="4712", SYMLINK+="masterCRD", MODE="0666"

An example udev-rule for Smargo SmartReader and Triple Reader+ [1]:

# File: /etc/udev/rules.d/45-smargo-reader.rules
############################## smargo tripple ###########################
SUBSYSTEMS=="usb", ATTRS{interface}=="Triple Reader+", ATTRS{../serial}=="12345678", ATTRS{bInterfaceNumber}=="01", SYMLINK+="sc/my-special-card", GOTO="smargo_tripple_end"
SUBSYSTEMS=="usb", ATTRS{interface}=="Triple Reader+", SYMLINK+="sc/triple-$attr{../serial}-$attr{bInterfaceNumber}"
LABEL="smargo_tripple_end"
############################## smargo stick ##############################
SUBSYSTEMS=="usb", KERNEL=="ttyUSB*", ATTRS{serial}=="Reader 1234567", SYMLINK+="sc/my-very-important-card"

Finally, modify oscam.server as follows:

[reader]
label               = my_smargo1
protocol            = smartreader     # or "mouse"
device              = Serial:Reader 1 # /dev/smargo1, if "mouse"
detect              = cd
mhz                 = 600
cardmhz             = 600
emmcache            = 1,3,2
group               = 1

[reader]
label               = my_smargo2
protocol            = mouse           # or "smartreader"
device              = /dev/smargo2    # Serial:Reader 2, if "smartreader" 
detect              = cd
mhz                 = 368
cardmhz             = 368
emmcache            = 1,3,2
group               = 2

# and so on...

Diese Seite in anderen Sprachen - This page in other languages - Cette page dans d'autres langues - Queste pagine in altre Lingue

[[OSCam/de/{{#titleparts:OSCam/en/examples/Reader|3|3}}|Deutsch]] [[OSCam/en/{{#titleparts:OSCam/en/examples/Reader|3|3}}|English]] [[OSCam/fr/{{#titleparts:OSCam/en/examples/Reader|3|3}}|Français]] [[OSCam/it/{{#titleparts:OSCam/en/examples/Reader|3|3}}|Italiano]]